S6730-H24X6C Overview
Huawei CloudEngine S6730-H series full-featured 10 GE switches
are Huawei's new-generation fixed switches ,to provide 10 GE
downlink ports as well as 100 GE uplink ports.
S6730-H24X6C Specification
Item | Description |
Memory (RAM) | 4 GB |
Flash | 2 GB in total. To view the available flash memory size, run the display version command. |
Mean time between failures (MTBF) | 62.27 years |
Mean time to repair (MTTR) | 2 hours |
Availability | > 0.99999 |
Service port surge protection | N/A |
Power supply surge protection | · Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode · Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode |
Dimensions (H x W x D) | · Basic dimensions (excluding the parts protruding from the body): · 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.) · Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 456.0 mm (1.72 in. x 17.4 in. x 17.6 in.) |
Weight (with packaging) | 8.9 kg (19.62 lb) |
Stack ports | · Any 10GE SFP+ ports (a maximum of 16 physical ports) · Any 40GE QSFP+ ports (a maximum of 6 physical ports) |
RTC | Supported |
RPS | Not supported |
PoE | Not supported |
Rated voltage range | · AC input: 100 V AC to 240 V AC, 50/60 Hz · High-Voltage DC input: 240 V DC · DC input: -48 V DC to -60 V DC |
Maximum voltage range | · AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz · High-Voltage DC input: 190 V DC to 290 V DC · DC input: -38.4 V DC to -72 V DC |
Maximum power consumption (100% throughput , full speed of fans ) | 254 W |
Typical power consumption (30% of traffic load, tested according to ATIS standard) | 149 W |
Operating temperature | -5°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0°C (32°F).
|
Storage temperature | -40°C to +70°C (-40°F to +158°F) |
Noise under normal temperature (27°C, sound power) | < 65 dB(A) |
Relative humidity | 5% to 95%, noncondensing |
Operating altitude | 0-5000 m (0-16404 ft.) |
Certification | · EMC certification · Safety certification · Manufacturing certification |
Part number | 02352FSG 02352FSG-001 02352FSG-005 02352FSG-007 02353GFC 02353GFC-001 02353GFC-003 02353GFC-004 |
Product Details
Figure 1 shows the appearance of S6730-H24X6C .
1 | Twenty-four 10GE SFP+ ports Applicable modules and cables: · GE optical module · GE-CWDM optical module · GE-DWDM optical module · GE copper module (100M/1000M auto-sensing supported in V200R009 and later versions) · 10GE SFP+ optical module (OSXD22N00 not supported) · 10GE-CWDM optical module · 10GE-DWDM optical module (applicable in V200R009C00 and later versions) · 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables · 3 m and 10 m SFP+ AOC cables · 0.5 m and 1.5 m SFP+ dedicated stack cables (supported by the last 16 SFP+ ports and used only for zero-configuration stacking) | 2 | Six 40GE QSFP+ ports Applicable modules and cables: · QSFP+ optical module · QSFP28+ optical module · 1 m, 3 m, and 5 m QSFP+ to QSFP+ high-speed copper cables · 10 m QSFP+ to QSFP+ AOC cable · 1 m QSFP28 to QSFP28 high-speed copper cable · 10 m QSFP28 to QSFP28 AOC cable · 2 m QSFP28 dedicated stack cable (supported in V200R020C10 and later versions)
NOTE: A QSFP28 optical port cannot be split into four 10GE ports, regardless of whether the port uses a QSFP28 or QSFP+ optical module.For the S6730-H24X6C (part number: 02352FSG/02352FSG-001/02352FSG-005/ 02352FSG-007): · By default, the license is not loaded on a switch. · In V200R013C02, QSFP28 ports are 100GE ports. · In V200R019C00 and later versions, QSFP28 ports are 40GE ports. To use the 100GE rate, you need to purchase and activate a license. · After a switch is upgraded from V200R013C02 to V200R019C00 or a later version, QSFP28 ports are still 100GE ports. You can load a license to change the port rate. · To configure QSFP28 ports as 100GE ports, load and activate this license, run the assign port-speed 100GE [ slot slot-id | all ] or assign port-type 100GE [ slot slot-id | all ] command, and restart the switch. In versions earlier than V200R020C00, the command format is assign port-speed 100GE [ slot slot-id | all ]. In V200R020C00 and later versions, the command format is assign port-type 100GE [ slot slot-id | all ]. For the S6730-H24X6C (part number: 02353GFC/02353GFC-001/ 02353GFC-003/02353GFC-004), the license has been activated and QSFP28 ports on the switch work as 100GE ports.
|
3 | Ground screw NOTE: It is used with a ground cable. | 4 | SSD card slot NOTE: This slot is reserved for future use. |
5 | One console port | 6 | One ETH management port |
7 | One USB port | 8 | One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.
|
9 | Fan module slot 1 NOTE: Applicable fan module: FAN-031A-B (Fan box (B, FAN panel side exhaust)) | 10 | Fan module slot 2 NOTE: Applicable fan module: FAN-031A-B (Fan box (B, FAN panel side exhaust)) |
11 | Fan module slot 3 NOTE: Applicable fan module: FAN-031A-B (Fan box (B, FAN panel side exhaust)) | 12 | Fan module slot 4 NOTE: Applicable fan module: FAN-031A-B (Fan box (B, FAN panel side exhaust)） |
| 13 | Power module slot 1 NOTE: Applicable power module: (600 W AC Power Module) (600 W AC Power Module) (600 W AC Power Module) (applicable in V200R020C10 and later versions) (1000 W DC Power Module)
| 14 | Power module slot 2 NOTE: Applicable power module: (600 W AC Power Module) (600 W AC Power Module) (600 W AC Power Module) (applicable in V200R020C10 and later versions) (1000 W DC Power Module) |
The Accessories
Table 2 shows the recommended transceivers, card and power module.
Models | Descriptions |
Optical Transceiver,eSFP,GE,Single-mode Module(1550nm,100km,LC) | |
Optical Transceiver,eSFP,GE,BIDI Single-mode Module(TX1310/RX1490,10km,LC) | |
Optical Transceiver,eSFP,GE,BIDI Single-mode Module(TX1490/RX1310,10km,LC) | |
Optical Transceiver,eSFP,GE,BIDI Single-mode Module(TX1310/RX1490,40km,LC) | |
Optical Transceiver,eSFP,GE,BIDI Single-mode Module(TX1490/RX1310,40km,LC) | |
Optical Transceiver,eSFP,GE,BIDI Single-mode Module(1570nm (Tx)/1490nm(Rx),80km,LC) | |
Optical Transceiver,eSFP,GE,BiDi Single-mode Module (1490nm(Tx)/1570nm(Rx),80km,LC) | |
1000Base,BIDI Optical Transceiver,SFP,GE,Single-mode Module (TX1490nm/RX1310nm,10km,SC) | |
CWDM Optical Transceiver,eSFP,2.5G,Single-mode Module (1471nm,80km,LC) | |
CWDM Optical Transceiver,eSFP,2.5G,Single-mode Module (1491nm,80km,LC) | |
DWDM Optical Transceiver,eSFP,2.5G,Single-mode Module (1560.61nm,120km,LC) | |
Electrical Transceiver,SFP,GE,Electrical Interface Module(100m,RJ45) | |
10GBase-USR Optical Transceiver,SFP+,10G,Multi-mode Module (850nm,0.1km,LC) | |
Optical Transceiver,SFP+,10G,Multi-mode Module(850nm,0.3km,LC) | |
Optical Transceiver,SFP+,10G,Single-mode Module(1310nm,1.4km,LC) | |
Optical Transceiver,SFP+,10G,Single-mode Module(1310nm,10km,LC) | |
Optical Transceiver,SFP+,10G,Single-mode Module(1550nm,40km,LC) | |
Optical Transceiver,SFP+,10G,Single-mode Module(1310nm,40km,LC) | |
10GBase-ZR Optical Transceiver,SFP+,10G,Single-mode Module (1550nm,80km,LC) | |
10GBase,BIDI Optical Transceiver,SFP+,10G,Single-mode Module (TX1270nm/RX1330nm,10km,LC) |
Get More Information
Do you have any question about the Huawei S6730-H24X6C ?
Contact us now via Live Chat or andy@ryderwell.com.
